AGCO Corporation has released the second 2020 Fendt Momentum Crop Tour field update. This update reports AGCO agronomists’ observations of tire-track compaction on plant growth.

Soil compaction caused by wheel traffic is an increasing concern among farmers, especially due to the weight of high-capacity, central-fill planters on the center transport wheels. Several studies have documented plant height reductions caused by compaction, which restricts root growth, limits nutrient and water uptake and ultimately lowers yield.

For example, researchers at Penn State reported that tires inflated to 100 pounds per square inch created compaction that reduced corn plant height at six weeks after planting by 21% compared to the control (no compaction), reducing grain yield by 11%. See Figure 1. In contrast, the researchers noted that flotation-style tires inflated to 36 psi “helped to reduce the effect of compaction on plant growth” to the extent that the crop height in that treatment was near that of the control.

In keeping with the 2020 AGCO Crop Tour goal to demonstrate the effects of and ways to minimize soil compaction at planting, AGCO agronomists have been observing crop development in plots in several states this summer. They recently recorded corn plant heights at growth stages after V12 to compare the compaction effects of various treatments.

In a plot near Casselton, North Dakota, they compared two planter tire-pressure inflation rates: 55 psi, similar to the level for road transport, and automated inflation that maintained tire pressure at approximately 17 psi.

Jason Lee, AGCO agronomist and farm solutions specialist, measured plant height in the rows on either side of the in-line tandem center transport tires of the Fendt Momentum planter at low and high tire inflation pressure. He observed a near 3-inch height advantage in corn planted with very high flexion (VF) tires auto adjusted to maintain a low psi (approx. 17 psi), as opposed to the same tires kept at a constant 55 psi. See Figure 2.

To illustrate the difference in soil compaction at different tire inflation rates, this photo shows the footprints made by the same VF tire at 55 psi on the left and 15 psi on the right, the minimum inflation recommended by the tire manufacturer.

Lee says:

“Note that the length of the footprint increases as tire pressure decreases, reducing pressure applied to the ground and therefore potential surface compaction. A larger footprint reduces the pressure to the soil and therefore lessens the potential for surface compaction damage.”

Evaluating correlation between plant height observations and yield

As the Casselton crop height observation suggests and many additional university studies have shown, tire inflation can make a difference in compaction and resulting plant height. Lee says he looks forward to taking the AGCO Crop Tour plots to harvest to see how final yields match with in-season observations.

Lee also says producers may want to consider lowering the inflation level of tractor and implement tires when possible before starting any field work. He acknowledges, however, that doing so means having an air compressor in the field and time to inflate tires back to road levels before transport, unless the equipment has a central tire inflation system, like VarioGrip on Fendt tractors or the tire inflation system available on the Fendt Momentum planter.

Source: AGCO

The post Agco presents Crop Tour field report about tire pressure and crop height appeared first on North America FarmQuip Magazine.

There will be three unique application crop tour plots located in the US, including a cotton plot in Tifton, Georgia and two soybean plots in the Midwest – one in Farmer City, Illinois and another in Vincent, Iowa.  The application crop tour is geared to gather data and insights that will help educate growers and commercial applicators on the impact of key variables in the application process. 

Four overarching protocols will be administered and reviewed during the 2020 growing season:

• Boom Height – How varied boom heights affect spray efficacy, consistency and accuracy
• Boom Contamination – Contamination and the risk of crop damage
• Boom Priming – The risks and impacts associated with boom priming, weed resistance and crop damage
• Nozzle Selection and Droplet Size – How proper selection of nozzles for speed and droplet size impact the application.

David Webster, application director at AGCO, is excited about the idea of demonstrating these impacts.

“If you think about the significant input costs a grower has with herbicide, pesticide and fungicide, it is critically important that the job gets done with a high degree of quality.  It’s really all about efficacy, and that’s what we’re looking to showcase with these plots.”

Webster said.

The application team will utilize several methodologies to measure the impact of the variables, and ultimately, yield results.  Over the next several months, AGCO will be releasing digital content related to the tours, including video, photos, and discussion related to the application protocols and the results they’re seeing in the field.

Source: AGCO Corporation

The post AGCO launches 2020 Application Crop Tour appeared first on North America FarmQuip Magazine.